how to remove soap scum from bathtub

When the minerals in water and soap fat mix, you create a very unpleasant reaction called soap scum. This winning, or losing, combination forms a whitish-yellow scaly, crust that lines your shower and tub walls, along with your shower doors. It can also get thicker the longer that it is left, creating that unpleasant bathroom ring. Since it isn’t an option not to use soap or shower, best to learn how to clean this difficult mess up.Discover MoreREAD MORECreative Mango Mocktail Drinks to Mix It Up| LoveToKnow

Homemade Soap Scum Cleaner

Cleaning soap scum can be hard to remove despite your best efforts. It can mar your glass, tiles, fixtures, and tub. Not only that, but the longer it sits the harder it can be to clean. Before you reach for commercial cleaners, there are a few tricks that you can try with ingredients in your pantry. For these homemade recipes, you’ll need:

  • Baking soda
  • White vinegar
  • Dish soap (Dawn recommended)
  • Spray bottle
  • Sponge
  • Soft bristle brush
  • Hydrogen peroxide
  • Bowl
  • Cloth

1. How to Remove Soap Scum From Shower Walls

If you are looking to clean your glass, fixtures, shower walls or shower doors, you can try a vinegar spray. Not only will it take away the white dingy glaze, but it can restore your shine.

  1. In a clean spray bottle combine 1 cup of water and 1 cup of vinegar. For an extra kick, add a tablespoon of dish soap.
  2. Give it a good shake and spray down your shower walls, fixtures, and glass doors.
  3. Allow it to sit for about 20 minutes or so.
  4. Using the sponge, scrub in slow circles.
  5. For particularly scaly areas, bust out the soft bristle brush.
  6. Rinse and repeat as necessary.

2. Clean Soap Scum in Tubs and Sinks

The inside of your fiberglass or porcelain tub and sink can see the brunt of soap scum if you take baths or have really hard water. For these areas, you might want a little more fighting power. In this instance baking soda works great, because it adds a bit of grit to scrub that soap scum. To clean soap scum, you’ll need to:

  1. Add a cup of baking soda to about 1/4 to 1/3 cup of vinegar. (You’re looking to make a scrubbing paste.)
  2. Let it foam.
  3. Using a sponge, add the paste to the tub or sink, paying special attention to thick soap scum areas.
  4. Allow it to sit on the tub or sink for 20-30 minutes.
  5. Using the brush, scrub the entire area in circular motions.
  6. Rinse and repeat as necessary.
Baking Soda And Vinegar Bottle

3. How to Clean Years of Soap Scum

Vinegar and baking soda are a powerful combination. However, if you have years of soap scum removal, it’s just not going to be tough enough. Hydrogen peroxide has all the power of vinegar, but with a bleaching agent that is great for those really tough stains. To use this tough homemade stain fighter, follow these steps.

  1. Mix 2 cups baking soda to 1 cup of hydrogen peroxide. If you need a smaller batch, just mix it 2:1.
  2. Using a cloth, apply the paste to the soap scum.
  3. Let it do its thing for at least an hour.
  4. Add a little water.
  5. Use the brush to scrub the tub in circular motions. Paying special attention to thick soap scum.
  6. Add baking soda to the brush and give it a little elbow grease for the toughest areas.
  7. Rinse and repeat as necessary until it’s all gone.

4. Removing Soap Scum From Tiles

When it comes to your tile walls, grab the Dawn and vinegar. These two are like a prize fighter when it comes to soap scum removal on your tiles.

  1. Heat up 1-2 cups of vinegar in the microwave for 30 seconds. You want it warm, not boiling.
  2. Add equal amounts of Dawn to a spray bottle.
  3. Pour in the heated vinegar.
  4. Shake to mix.
  5. Spray down the tiles.
  6. Allow the mixture to sit for 25-45 minutes.
  7. Wipe it down with a warm sponge.
  8. For any remaining soap scum, add a little baking soda to the sponge and scrub in circular motions.

Leave a Comment