how to charge battery with dc power supply

How to Charge a Battery with a DC Power Supply: a blog about how to charge your battery for your back up kit.

How to Make 12v Battery Charger With Old SMPS - YouTube

How to Charge a Battery with a DC Power Supply

Battery charging is an important part of getting the most out of your device. In this article, we’ll show you how to charge your battery with a DC power supply.

What You’ll Need

-DC power supply

-9V battery terminal clips (with spade lugs)

-9V battery (optional)

There are several ways to charge batteries with a dc power supply. One method involves using a converter, which is a special piece of equipment that can be used to convert DC power into AC power. Another method involves connecting the battery directly to a generator, which is another way to convert DC power into AC power.

The first step in charging a battery with a dc power supply is connecting it to the battery charger via two wires. The red wire should be connected to the positive terminal of the battery, while the black wire should be connected to the negative terminal of the battery. These wires should then be connected directly to their corresponding terminals on the charger itself (positive terminal goes directly into positive terminal).

After this has been completed, you can plug in your charger and turn it on by flipping its switch from “off” to “on.” Once turned on, most chargers will automatically begin charging your battery; however, some require manual input before they will start charging. If this is necessary for your particular model of charger, consult its user manual for instructions on how to activate it manually.

When charging has finished (which may take anywhere from an hour up), unplug your charger from its outlet and disconnect all wires from your battery

To charge a battery using a DC power supply, you will need a DC power supply, a battery charger and some batteries.

First, take your battery and connect it to the positive terminal on your power supply. Then connect the negative terminal of the power supply to the negative terminal of your battery. Finally, connect your load to either terminal and turn on the power supply. Your load should now be charging.

If you want to charge your battery with a DC power supply, there are a few things you need to know.

First, you’ll need a charging circuit that can output the voltage and current needed to charge your battery. You’ll also need a way to connect the battery to the charging circuit—either through wires or by using a connector like an Anderson Power Pole (APC) or Molex Mini-Fit Jr. connector.

When connecting wires to your battery, be sure not to cross any lines—you don’t want any possible short circuits on your device!

Once you’ve got everything connected together, you can use some simple math to figure out how long it will take for your battery to charge up:

  1. Calculate the current draw of all devices connected to your battery pack. This can be done by multiplying their wattage (W) by their voltage (V). For example, if you’re powering three LEDs that each draw 2W at 12V, then their total power draw would be 3W x 12V = 36V.
  2. Find out how much current your charger can output at its maximum setting and divide that number by the total current draw of all devices connected

If you’re using a DC power supply to charge your battery, it’s important to follow a few rules.

First, make sure that the polarity of the power supply matches up with the polarity of your battery. If not, you could damage your battery or even start a fire!

Then, set up your charger according to the manufacturer’s directions. You may need to connect it to a power strip or plug-in unit in order to use it safely.

Now that everything is ready, connect one end of the charger cable to a socket on the back of your battery and then plug in the other end into an outlet or wall socket. It’s important that you don’t use an extension cord for this part because it could cause problems with voltage levels and other safety factors.

The first thing you’ll need to do is connect your battery to the power supply.

Take your battery’s negative terminal (the one without the “+” sign) and connect it to the negative terminal on your power supply with a red wire. Then take the positive terminal (with the “+” sign) on your battery and connect it to one of the “+” terminals on your power supply with a black wire.

Next, take the other “+” terminal on your power supply and connect that to another black wire. Tie them together with a knot or solder them together so they don’t come apart.

Finally, take all three wires from your battery—the red, black, and second black—and connect them to their respective terminals on your device.

  1. Connect the positive terminal of the battery to the positive terminal of the power supply.
  2. Connect the negative terminal of the battery to the negative terminal of the power supply.
  3. Set your multimeter to read voltage. For this project, we are using a 9V battery and a 12V power supply, so we need to adjust our meter accordingly. Set it for 9V DC (direct current).
  4. Connect one probe of your multimeter to ground (the negative terminal on your power supply), and then connect your other probe to one end of your circuit (the positive end of your battery). Make sure that you are only measuring voltage here, not current! The meter should read somewhere between 7-10 volts for a standard AA battery in good condition, or about 4-5 volts for a standard AAA battery in good condition.

Leave a Comment